Das Treffen der Generationen

    Die Toyota Supra Community für alle Supra Generationen

    Toyota Supra A90

    Besitzer der fünften Generation des Toyota Supra sind begeistert, denn was Leistung und Fahrdynamik hat der neue Supra A90 alle Erwartungen übertroffen.

    Toyota Supra MKIV

    Bekannt aus dem Fast & Furious Film, kam im Juli 1993 die vierte und bisher letzte Generation des Toyota Supra auf den Markt. International wird dieser Typ "Supra MKIV" genannt.

    Toyota Supra MKIII

    Anfang 1986 wurde die dritte Generation des Supra vorgestellt. Sie ist zugleich die erste, die nicht mehr mit dem Namenszusatz Celica vermarktet wurde.

    Celica Supra (MK2)

    Die zweite Generation wurde im Herbst 1981 präsentiert und hatte mit dem neuen (170 PS) starken 6-Zylinder-Motoren einen komplett eigenständigen Antrieb.

    2000GT & Supra MK1

    Der von Frühjahr 1978 bis Sommer 1981 gebaute erste Supra wurde noch als Spitzenversion der Celica zuerst in Japan und später in den USA angeboten.

    Toyota Classics

    Fotos, Videos, Infos und mehr zum Toyota 2000GT & Celica XX Supra

    Toyota 2000GT & Celica Supra

    Der von Frühjahr 1978 bis Sommer 1981 gebaute erste Supra wurde noch als Spitzenversion der Celica zuerst in Japan und später in den USA angeboten.

    MK 2

    Fotos, Videos, Infos und mehr zum Toyota Supra MK2

    Celica Supra MKII (MA 60/61)

    Die zweite Generation wurde im Herbst 1981 präsentiert und hatte mit dem neuen (170 PS) starken 6-Zylinder-Motoren einen komplett eigenständigen Antrieb.

    MK 3

    Fotos, Videos, Infos und mehr zum Toyota 2000GT & Celica XX Supra

    Toyota Supra MKIII (MA70/MA71)

    Die zweite Generation wurde im Herbst 1981 präsentiert und hatte mit dem neuen (170 PS) starken 6-Zylinder-Motoren einen komplett eigenständigen Antrieb.

    MK 4

    Fotos, Videos, Infos und mehr zum Toyota Supra MKIV

    Toyota Supra MKIV (A80)

    Bekannt aus dem Fast & Furious Film, kam im Juli 1993 die vierte und bisher letzte Generation des Toyota Supra auf den Markt. International wird dieser Typ "Supra MKIV" genannt.

    MK 5

    Fotos, Videos, Infos und mehr zum neuen Toyota Supra A90

    Toyota Supra MKV (A90)

    Besitzer der fünften Generation des Toyota Supra sind begeistert, denn was Leistung und Fahrdynamik hat der neue Supra A90 alle Erwartungen übertroffen.
    Modelle: ClassicsMK2MK3MK4MK5
    Repair Manual

    Cylinder block reassembly - 2JZ-GTE Engine - Toyota Supra A80

    
    • Thoroughly clean all parts to be assembled.
    • Before installing the parts, apply fresh engine oil to all sliding and rotating surfaces.
    • Replace all gaskets, O-rings and oil seals with new parts.
    1. Assemble piston and connecting rod
      1. Install a new snap ring at one end of the piston pin hole.
        Be sure that end gap of the snap ring is not aligned with the pin hole cutout portion of the piston.
      2. Gradually heat the piston to about 80°C (176°F).
      3. Coat the piston pin with engine oil.
      4. Align the front marks of the piston and connecting rod, and push in the piston pin with your thumb.
      5. Install a new snap ring at the other end of the piston pin hole.
        Be sure that end gap of the snap ring is not aligned with the pin hole cutout portion of the piston.
    2. Install piston rings
      1. Install the oil ring expander and 2 side rails by hand.
      2. Using a piston ring expander, install the 2 compression rings with the code mark facing up.
        Code mark:
        No.1 2T
        No.2 2N
      3. Position the piston rings so that the ring ends are as shown.
        Do not align the piston ring ends.
    3. Install bearings
      1. Align the bearing claw with the groove of the connecting rod and connecting cap.
      2. Install the bearings in the connecting rod and connecting rod cap.
      Apply a generous amount of oil on the sliding surface of the bearing, and not on the back of it or on the surface to which it is installed.
    4. Install oil nozzles (with relief valves) Using a 5 mm hexagon wrench, install the oil nozzle with the bolt. Install the 6 oil nozzles.
      Torque: 8.8 N·m (90 kgf·cm, 78 in.·lbf)
    5. Install main bearings
      • Main bearings come in widths of 20.0 mm (0.787 in.) and 23.0 mm (0.906 in.). Install the 23.0 mm bearings in the No.1 cylinder block journal position with the main bearing cap. Install the 20.0 mm bearings in the other positions.
      • Upper bearings have an oil groove and oil holes; lower bearings do not.
      1. Align the bearing claw with the claw groove of the main bearing cap or cylinder block.
        Install the bearing with the oil hole in the cylinder block.
      2. Install the bearings in the cylinder block and main bearing caps.
    6. Install upper thrust washers
      Install the 2 thrust washers under the No.4 main journal position of the cylinder block with the oil grooves facing outward.
    7. Place crankshaft on cylinder block
    8. Place main bearing cap and lower thrust washers on cylinder block
      1. Install the lower thrust washers on the No.4 main bearing with the grooves facing outward.
      2. Install the main bearing caps in numerical order with the arrows facing forward.
    9. Install main bearing cap bolts
      • The main bearing cap bolts are tightened in 2 progressive steps (steps (b) and (d)).
      • If any of the main bearing bolts break or deform, replace them.
      1. Apply a light coat of engine oil on the threads and under the heads of the main bearing cap bolts.
      2. Install and uniformly tighten the 14 main bearing cap bolts, in several passes, in the sequence shown.
        Torque: 44 N·m (450 kgf·cm, 33 ft·lbf)
        If any one of the main bearing cap bolts does not meet the torque specification, replace the main bearing cap bolt.
      3. Mark the front of the main bearing cap bolt head with paint.
      4. Retighten the main bearing cap bolts 90° in the numerical order shown above.
      5. Check that the painted mark is now at a 90° angle to the front.
      6. Check that the crankshaft turns smoothly.
    10. Check crankshaft thrust clearance (See page EM-71 )
    11. Install piston and connecting rod assemblies Using a piston ring compressor, push the correctly numbered piston and connecting rod assemblies into each cylinder with the front mark of the piston facing forward.
    12. Place connecting rod cap on connecting rod
      1. Match the numbered connecting rod cap with the connecting rod.
      2. Install the connecting rod cap with by aligning the dowel pin to the corresponding hole.
    13. Install connecting rod cap bolts
      • The connecting rod cap bolts are tightened in 2 progressive steps (steps (b) and (d)).
      • If any of the connecting rod bolts break or deform, replace them.
      1. Apply a light coat of engine oil on the threads and under the heads of the connecting rod cap bolts.
      2. At first, install and alternately tighten the bolts of the connecting rod cap in several passes.
        Torque: 29 N·m (300 kgf·cm, 22 ft·lbf)
        If any one of the connecting rod cap bolts does not meet the torque specification, replace the cap bolt.
      3. Mark the front of the connecting rod cap bolt with paint.
      4. Retighten the connecting rod cap bolts 90° in the numerical order shown.
      5. Check that the painted mark is now at a 90° angle to the front.
      6. Check that the crankshaft turns smoothly.
    14. Check connecting rod thrust clearance (See page EM-79 )
    15. Install rear oil seal retainer
      1. Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the retainer and cylinder block.
        • Using a razor blade and gasket scraper, remove all the old packing (FIPG) material from the gasket surfaces and sealing groove.
        • Thoroughly clean all components to remove all debris.
        • Using a non-residue solvent, clean both sealing surfaces.
      2. Apply seal packing to the retainer as shown in the illustration.
        Seal packing:
        Part No. 08826-00080 or equivalent
        • Install a nozzle that has been cut to a 2 - 3 mm (0.08 - 0.12 in.) opening.
        • Parts must be assembled within 3 minutes of application. Otherwise the material must be removed and reapplied.
        • Immediately remove nozzle from the tube and reinstall cap.
      3. Install the retainer with the 6 bolts.
        Torque: 6.0 N·m (60 kgf·cm, 53 in.·lbf)
    16. Install oil pump (See page LU-16 )
    17. Install water pump (See page CO-11)
    18. Install crankshaft position sensor
      Torque: 9.0 N·m (90 kgf·cm, 80 in.·lbf)
    19. Install RH engine mounting bracket and insulator assembly
      Torque: 59 N·m (590 kgf·cm, 44 ft·lbf)
    20. Install engine coolant drain plug
      Torque: 30 N·m (300 kgf·cm, 22 ft·lbf)
    21. Install union for oil cooler hose
      1. Apply adhesive to 2 or 3 threads of the union.
        Adhesive:
        Part No. 08833-00070, THREE BOND 1324, or equivalent
      2. Install the union.
        Torque: 40 N·m (400 kgf·cm, 30 ft·lbf)
    22. Install oil pressure switch and knock sensors
      1. Install the union nut with a new gasket.
        SST 09816-30010
        Torque: 55 N·m (550 kgf·cm, 41 ft·lbf)
      2. Apply adhesive to 2 or 3 threads of the oil pressure switch.
        Adhesive:
        Part No. 08833-00080, THREE BOND 1344, LOCKTITE 242 or equivalent
      3. Using SST, install the switch and sensors.
        SST 09816-30010
        Torque:
        OIl pressure switch: 14 N·m (150 kgf·cm, 11 ft·lbf)
        Knock sensor: 44 N·m (450 kgf·cm, 33 ft·lbf)
    23. Install fuel pipe support
      Torque: 28 N·m (290 kgf·cm, 21 ft·lbf)
    24. Install LH engine mounting bracket and insulator assembly
      Torque: 58 N·m (590 kgf·cm, 44 ft·lbf)
    25. Install oil filter bracket
      1. Check and clean the oil filter bracket installation.
      2. Place a new O-ring in position on the oil filter bracket.
      3. Apply clean engine oil to the O-ring.
      4. Install a new gasket to the union bolt.
      5. Install the oil filter bracket with the union bolt.
        Torque: 90 N·m (900 kgf·cm, 66 ft·lbf)
    26. Install No.2 water bypass pipe with hose
      1. Install a new gasket to the water pump.
      2. Install the water bypass pipe with the 2 bolts and 2 nuts.
        Torque: 21 N·m (210 kgf·cm, 15 ft·lbf)
    27. Install oil cooler (See page LU-22 )
    28. Install cylinder head (See page EM-47 )
    29. Install timing pulleys and belt (See page EM-21 )
    30. Install generator (See page CH-18 )
    31. Remove engine stand from engine
    32. M/T:
      Install flywheel
      The flywheel bolts are tightened in 2 progressive step, (b) and (d).
      1. Install the flywheel on the crankshaft.
      2. Install and uniformly tighten the 8 bolts, in several passes, in the sequence shown.
        Torque: 49 N·m (500 kgf·cm, 36 ft·lbf)
      3. Mark the flywheel bolt with paint.
      4. Retighten the flywheel bolts by an additional 90°.
      5. Check that the painted mark is now at a 90° angle to (d).
    33. A/T:
      Install drive plate
      1. Install the front spacer, drive plate and rear plate on the crankshaft.
      2. Apply adhesive to 2 or 3 threads of the mounting bolt end.
        Adhesive:
        Part No. 08833-00070, THREE BOND 1324 or equivalent
      3. Install and uniformly tighten the 8 bolts, in several passes, in the sequence shown.
        Torque: 83 N·m (850 kgf·cm, 61 ft·lbf)
    This guide is based on the book edition Toyota (RM502U, 1997)
    Oxwall Community Software